Need Help? Hire Us Now!

 

 

The content following next about How to Install a Bathtub is truly fascinating. Check it out yourself and decide what you think of it.

Installing a bathtub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately hard job. If the old tub is readily accessible, the task can relocate easily; if you need to open up a wall to remove the old bathtub and also position the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require a helper to vacate the old tub and embeded in the brand-new one. Make sure you have actually certified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider using one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have currently acquired a brand-new bathtub and also do not require to alter the plan of your previous water system pipes.
Your tools and material checklist should consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you require to replace old faucets with new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. When the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Installing the Bath tub

Utilizing both wood boards under its feet, place the tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bath tub till the spirit level reads degree.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and also check all joints and new pipework for leaks and also tighten them if essential. Fill the bathtub and also examine the overflow electrical outlet and also the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the tub ought to wait until the bathtub has been made use of at the very least when as this will certainly settle it into its final position.

 

 

Planning for the Installation

Firstly, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final placement.

 

 

Tiling Around the Tub

In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and installations. They are offered in tubes as well as cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can crack relatively very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or water resistant sticky as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I'm certainly very involved in How to Install a Bathtub Yourself and I hope you appreciated my page. So long as you enjoyed reading our post plz be sure to share it. Kudos for your time. Visit us again soon.

Here